10.3. Running a Design on Arty
10.3.1. Arty100T Instructions
The default Digilent Arty A7-100T harness uses a TSI-over-UART adapter to bringup the FPGA.
A user can connect to the Arty A7-100T target using a special uart_tsi
program that opens a UART TTY.
The interface for the uart_tsi
program provides unique functionality that is useful for bringing up test chips.
To build the design (Vivado should be added to the PATH
), run:
cd fpga/
make SUB_PROJECT=arty100t bitstream
To build the UART-based frontend server, run:
cd generators/testchipip/uart_tsi
make
After programming the bitstream, and connecting the Arty’s UART to a host PC via the USB cable, the uart_tsi
program can be run to interact with the target.
Running a program:
./uart_tsi +tty=/dev/ttyUSBX dhrystone.riscv
Probe an address on the target system:
./uart_tsi +tty=/dev/ttyUSBX +init_read=0x10000 none
Write some address before running a program:
./uart_tsi +tty=/dev/ttyUSBX +init_write=0x80000000:0xdeadbeef none
Self-check that binary loading proceeded correctly:
./uart_tsi +tty=/dev/ttyUSBX +selfcheck dhrystone.riscv
Run a design at a higher baud rate than default (For example, if CONFIG=UART921600RocketArty100TConfig
were built):
./uart_tsi +tty=/dev/ttyUSBX +baudrate=921600 dhrystone.riscv
10.3.2. Arty35T Legacy Instructions
The default Digilent Arty A7-35T harness is setup to have JTAG available over the board’s PMOD pins, and UART available over its FTDI serial USB adapter. The pin mappings for JTAG signals are identical to those described in the SiFive Freedom E310 Arty 35T Getting Started Guide.
The JTAG interface allows a user to connect to the core via OpenOCD, run bare-metal applications, and debug these applications with gdb. UART allows a user to communicate with the core over a USB connection and serial console running on a PC.
To extend this design, a user may create their own Chipyard configuration and add the WithArtyTweaks
located in fpga/src/main/scala/arty/Configs.scala
.
Adding this config. fragment will enable and connect the JTAG and UART interfaces to your Chipyard design.
class WithArtyTweaks extends Config(
new WithArtyDebugResetHarnessBinder ++
new WithArtyJTAGResetHarnessBinder ++
new WithArtyJTAGHarnessBinder ++
new WithArtyUARTHarnessBinder ++
new WithDebugResetPassthrough ++
new chipyard.harness.WithHarnessBinderClockFreqMHz(32) ++
new chipyard.harness.WithAllClocksFromHarnessClockInstantiator ++
new chipyard.config.WithSystemBusFrequency(32) ++
new chipyard.config.WithFrontBusFrequency(32) ++
new chipyard.config.WithControlBusFrequency(32) ++
new chipyard.config.WithPeripheryBusFrequency(32) ++
new chipyard.config.WithControlBusFrequency(32) ++
new testchipip.serdes.WithNoSerialTL ++
new testchipip.soc.WithNoScratchpads
)
class TinyRocketArtyConfig extends Config(
new WithArtyTweaks ++
new freechips.rocketchip.rocket.WithNBreakpoints(2) ++
new chipyard.TinyRocketConfig
)
Future peripherals to be supported include the Arty A7-35T SPI Flash EEPROM, and I2C/PWM/SPI over the Arty A7-35T GPIO pins. These peripherals are available as part of sifive-blocks.
10.3.3. Brief Implementation Description and Guidance for Adding/Changing Xilinx Collateral
Like the VCU118, the basis for the Arty A7-35T design is the creation of a special test harness that connects the external IO (which exist as Xilinx IP blackboxes) to the Chipyard design.
This is done with the ArtyTestHarness
in the basic default Arty A7-35T target. However, unlike the VCU118TestHarness
, the ArtyTestHarness
uses no Overlays
, and instead directly connects chip top IO to the ports of the external IO blackboxes, using functions such as IOBUF
provided by fpga-shells
.
Unlike the VCU118 and other more complicated test harnesses, the Arty A7-35T Vivado collateral is not generated by Overlays
, but rather are a static collection of create_ip
and set_properties
statements located in the files within fpga/fpga-shells/xilinx/arty/tcl
and fpga/fpga-shells/xilinx/arty/constraints
.
If the user wishes to re-map FPGA package pins to different harness-level IO, this may be changed within fpga/fpga-shells/xilinx/arty/constraints/arty-master.xdc
. The addition of new Xilinx IP blocks may be done in fpga-shells/xilinx/arty/tcl/ip.tcl
, mapped to harness-level IOs in arty-master.xdc
, and wired through from the test harness to the chip top using HarnessBinders
and IOBinders
.
Examples of a simple IOBinder
and HarnessBinder
for routing signals (in this case the debug and JTAG resets) from the core to the test harness are the WithResetPassthrough
and WithArtyResetHarnessBinder
.