5.8. Sky130 Commercial Tutorial

The vlsi folder of this repository contains an example Hammer flow with the TinyRocketConfig from Chipyard. This example tutorial uses the built-in Sky130 technology plugin and requires access to the included Mentor tool plugin submodule, which is needed for DRC & LVS.

5.8.1. Project Structure

This example gives a suggested file structure and build system. The vlsi/ folder will eventually contain the following files and folders:

  • Makefile, sim.mk, power.mk

    • Integration of Hammer’s build system into Chipyard and abstracts away some Hammer commands.

  • build

    • Hammer output directory. Can be changed with the OBJ_DIR variable.

    • Will contain subdirectories such as syn-rundir and par-rundir and the inputs.yml denoting the top module and input Verilog files.

  • env.yml

    • A template file for tool environment configuration. Fill in the install and license server paths for your environment. For SLICE and BWRC affiliates, example environment configs are found here.

  • example-vlsi-sky130

    • Entry point to Hammer. Contains example placeholders for hooks.

  • example-sky130.yml, example-tools.yml, example-designs/sky130-commercial.yml

    • Hammer IR for this tutorial. For SLICE and BWRC affiliates, an example ASAP7 config is found here.

  • example-design.yml, example-asap7.yml, example-tech.yml

    • Hammer IR not used for this tutorial but provided as templates.

  • generated-src

    • All of the elaborated Chisel and FIRRTL.

  • hammer-<vendor>-plugins

    • Tool plugin repositories.

5.8.2. Prerequisites Quick Prerequisite Setup

As of recently, the Sky130A PDK may be installed via conda. The prerequisite setup for this tutorial may eventually be scripted, but for now the directions to set them up are below.

# download all files for Sky130A PDK
conda create -c litex-hub --prefix ~/.conda-sky130 open_pdks.sky130a=1.0.457_0_g32e8f23
# clone the SRAM22 Sky130 SRAM macros
git clone https://github.com/rahulk29/sram22_sky130_macros ~/sram22_sky130_macros

5.8.3. Initial Setup

In the Chipyard root, ensure that you have the Chipyard conda environment activated. Then, run:

./scripts/init-vlsi.sh sky130

to pull and install the plugin submodules. Note that for technologies other than sky130 or asap7, the tech submodule must be added in the vlsi folder first.

Now navigate to the vlsi directory. The remainder of the tutorial will assume you are in this directory. We will summarize a few files in this directory that will be important for the rest of the tutorial.

cd ~chipyard/vlsi example-vlsi-sky130

This is the entry script with placeholders for hooks. In the ExampleDriver class, a list of hooks is passed in the get_extra_par_hooks. Hooks are additional snippets of python and TCL (via x.append()) to extend the Hammer APIs. Hooks can be inserted using the make_pre/post/replacement_hook methods as shown in this example. Refer to the Hammer documentation on hooks for a detailed description of how these are injected into the VLSI flow. example-sky130.yml

This contains the Hammer configuration for this example project. Example clock constraints, power straps definitions, placement constraints, and pin constraints are given. Additional configuration for the extra libraries and tools are at the bottom.

Add the following YAML keys to the top of this file to specify the location of the Sky130A PDK and SRAM macros.

# all ~ should be replaced with absolute paths to these directories
# technology paths
technology.sky130.sky130A: ~/.conda-sky130/share/pdk/sky130A
technology.sky130.sram22_sky130_macros: ~/sram22_sky130_macros example-tools.yml

This contains the Hammer configuration for a commercial tool flow. It selects tools for synthesis (Cadence Genus), place and route (Cadence Innovus), DRC and LVS (Mentor Calibre).

5.8.4. Building the Design

To elaborate the TinyRocketConfig and set up all prerequisites for the build system to push the design and SRAM macros through the flow:

make buildfile tutorial=sky130-commercial

The command make buildfile generates a set of Make targets in build/hammer.d. It needs to be re-run if environment variables are changed. It is recommended that you edit these variables directly in the Makefile rather than exporting them to your shell environment.

The buildfile make target has dependencies on both (1) the Verilog that is elaborated from all Chisel sources and (2) the mapping of memory instances in the design to SRAM macros; all files related to these two steps reside in the generated-src/chipyard.harness.TestHarness.TinyRocketConfig-ChipTop directory. Note that the files in generated-src vary for each tool/technology flow. This especially applies to the Sky130 Commercial vs OpenROAD tutorial flows, so these flows should be run in separate chipyard installations. If the wrong sources are generated, simply run make buildfile -B to rebuild all targets correctly.

For the purpose of brevity, in this tutorial we will set the Make variable tutorial=sky130-commercial, which will cause additional variables to be set in tutorial.mk, a few of which are summarized as follows:

  • CONFIG=TinyRocketConfig selects the target generator config in the same manner as the rest of the Chipyard framework. This elaborates a stripped-down Rocket Chip in the interest of minimizing tool runtime.

  • tech_name=sky130 sets a few more necessary paths in the Makefile, such as the appropriate Hammer plugin

  • TOOLS_CONF and TECH_CONF select the approproate YAML configuration files, example-tools.yml and example-sky130.yml, which are described above

  • DESIGN_CONF and EXTRA_CONFS allow for additonal design-specific overrides of the Hammer IR in example-sky130.yml

  • VLSI_OBJ_DIR=build-sky130-commercial gives the build directory a unique name to allow running multiple flows in the same repo. Note that for the rest of the tutorial we will still refer to this directory in file paths as build, again for brevity.

  • VLSI_TOP is by default ChipTop, which is the name of the top-level Verilog module generated in the Chipyard SoC configs. By instead setting VLSI_TOP=Rocket, we can use the Rocket core as the top-level module for the VLSI flow, which consists only of a single RISC-V core (and no caches, peripherals, buses, etc). This is useful to run through this tutorial quickly, and does not rely on any SRAMs.

5.8.5. Running the VLSI Flow Synthesis

make syn tutorial=sky130-commercial

Post-synthesis logs and collateral are in build/syn-rundir. The raw quality of results data is available at build/syn-rundir/reports, and methods to extract this information for design space exploration are a work in progress. Place-and-Route

make par tutorial=sky130-commercial

After completion, the final database can be opened in an interactive Innovus session via ./build/par-rundir/generated-scripts/open_chip.

Intermediate database are written in build/par-rundir between each step of the par action, and can be restored in an interactive Innovus session as desired for debugging purposes.

Timing reports are found in build/par-rundir/timingReports. They are gzipped text files. DRC & LVS

To run DRC & LVS, and view the results in Calibre:

make drc tutorial=sky130-commercial
make lvs tutorial=sky130-commercial

Some DRC errors are expected from this PDK, especially with regards to the SRAMs, as explained in the Sky130 Hammer plugin README. For this reason, the example-vlsi-sky130 script black-boxes the SRAMs for DRC/LVS analysis. Simulation

Simulation with VCS is supported, and can be run at the RTL- or gate-level (post-synthesis and post-P&R). The simulation infrastructure as included here is intended for running RISC-V binaries on a Chipyard config. For example, for an RTL-level simulation:

make sim-rtl tutorial=sky130-commercial BINARY=$RISCV/riscv64-unknown-elf/share/riscv-tests/isa/rv64ui-p-simple

Post-synthesis and post-P&R simulations use the sim-syn and sim-par make targets, respectively.

Appending -debug and -debug-timing to these make targets will instruct VCS to write a SAIF + FSDB (or VPD if the USE_VPD flag is set) and do timing-annotated simulations, respectively. See the sim.mk file for all available targets. Power/Rail Analysis

Post-P&R power and rail (IR drop) analysis is supported with Voltus:

make power-par tutorial=sky130-commercial

If you append the BINARY variable to the command, it will use the activity file generated from a sim-<syn/par>-debug run and report dynamic power & IR drop from the toggles encoded in the waveform.

To bypass gate-level simulation, you will need to run the power tool manually (see the generated commands in the generated hammer.d buildfile). Static and active (vectorless) power & IR drop will be reported. VLSI Flow Control

Firt, refer to the VLSI Flow Control documentation. The below examples use the redo-par Make target to re-run only place-and-route. redo- may be prepended to any of the VLSI flow actions to re-run only that action.

# the following two statements are equivalent because the
#   extraction step immediately precedes the write_design step
make redo-par HAMMER_EXTRA_ARGS="--start_after_step extraction"
make redo-par HAMMER_EXTRA_ARGS="--start_before_step write_design"

# example of re-running only floorplanning to test out a new floorplan configuration
#   the "-p file.yml" causes file.yml to override any previous yaml/json configurations
make redo-par \
  HAMMER_EXTRA_ARGS="--only_step floorplan_design -p example-designs/sky130-openroad.yml"